Safety data sheet reference · CAS 80-05-7
Bisphenol A SDS
also: bisphenol A MSDS · safety data sheet · (CH3)2C(C6H4OH)2 · CAS 80-05-7 · EC 201-245-8 · BPA
Official PDF from supplier
This page is a reference, not the legal document.
CAS number
80-05-7
EC number
201-245-8
CLP Annex VI index
604-030-00-0
Molecular formula
C15H16O2
Structural formula
(CH3)2C(C6H4OH)2
Molar mass
228.29 g/mol
§ 02 · Hazards identification
Bisphenol A harmonised EU classification
CLP Annex VI · Index 604-030-00-0. A supplier SDS may add self-classified hazards — this is the legal minimum.
Precautionary statements
Codes ending in a colon introduce the action that follows — on a label they are printed as combined statements, such as P305+P351+P338.
§ 03 · Composition and identifiers
Bisphenol A molecular structure
Bisphenol A is a molecular compound. The skeletal formula below is drawn from its PubChem SMILES string, and every value in this section is computed from that structure.
2D skeletal formula · (CH3)2C(C6H4OH)2
Functional groups
phenol, aromatic ring
Electron count
88 valence e⁻ · 4 lone pairs
Identifiers from PubChem (NIH, public domain). Structure diagram drawn with RDKit from the SMILES string. Geometry and hybridisation are computed from the connection table, not measured.
§ 04 · First-aid measures
Bisphenol A first aid measures
Call your national emergency number first. These are published first-aid measures, not medical advice, and they do not replace emergency services, a poison control centre or the supplier's safety data sheet.
§4–§6 below reproduce the CAMEO Chemicals entry 4,4'-ISOPROPYLIDENEDIPHENOL. CAMEO publishes response data per product entry, so the entry can describe a solution, a refrigerated liquid or a molten form rather than the pure substance in §9 — check it matches what you are handling.
EYES
First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop.
SKIN
IMMEDIATELY flood affected skin with water while removing and isolating all contaminated clothing. Gently wash all affected skin areas thoroughly with soap and water. If symptoms such as redness or irritation develop, IMMEDIATELY call a physician and be prepared to transport the victim to a hospital for treatment.
INHALATION
IMMEDIATELY leave the contaminated area; take deep breaths of fresh air. If symptoms (such as wheezing, coughing, shortness of breath, or burning in the mouth, throat, or chest) develop, call a physician and be prepared to transport the victim to a hospital. Provide proper respiratory protection to rescuers entering an unknown atmosphere. Whenever possible, Self-Contained Breathing Apparatus (SCBA) should be used; if not available, use a level of protection greater than or equal to that advised under Protective Clothing.
INGESTION
DO NOT INDUCE VOMITING. If the victim is conscious and not convulsing, give 1 or 2 glasses of water to dilute the chemical and IMMEDIATELY call a hospital or poison control center. Be prepared to transport the victim to a hospital if advised by a physician. If the victim is convulsing or unconscious, do not give anything by mouth, ensure that the victim's airway is open and lay the victim on his/her side with the head lower than the body. DO NOT INDUCE VOMITING. IMMEDIATELY transport the victim to a hospital.
Source: NTP, 1992 — via CAMEO Chemicals (NOAA), public domain.
§ 05 · Fire-fighting measures
Bisphenol A fire fighting measures
ERG 2024 · GUIDE 171 Substances (Low to Moderate Hazard)ERG guidance is written per response guide, not per substance — Guide 171 covers every material assigned to it, so a few sentences reference other UN numbers in the same group.
Fire and explosion hazard
This chemical is combustible. This compound may form explosive dust clouds. Static electricity can cause its dust to explode.
Extinguishing media and tactics
Fire Extinguishing Agents: Foam, dry chemical, carbon dioxide
Source: USCG, 1999 — via CAMEO Chemicals (NOAA), public domain. Entry: 4,4'-ISOPROPYLIDENEDIPHENOL.
§ 06 · Accidental release measures
Bisphenol A spill and leak response
Containment and clean-up
SMALL SPILLS AND LEAKAGEShould a spill occur while you are handling this chemical, FIRST REMOVE ALL SOURCES OF IGNITION, then you should dampen the solid spill material with 60-70% ethanol and transfer the dampened material to a suitable container. Use absorbent paper dampened with 60-70% ethanol to pick up any remaining material. Seal the absorbent paper, and any of your clothes, which may be contaminated, in a vapor-tight plastic bag for eventual disposal. Solvent wash all contaminated surfaces with 60-70% ethanol followed by washing with a soap and water solution. Do not reenter the contaminated area until the Safety Officer (or other responsible person) has verified that the area has been properly cleaned.
STORAGE PRECAUTIONSYou should store this chemical under ambient conditions, and keep it away from oxidizing materials.
Initial isolation and evacuation
IMMEDIATE PRECAUTIONARY MEASUREIsolate spill or leak area in all directions for at least 50 meters (150 feet) for liquids and at least 25 meters (75 feet) for solids.
SPILLIncrease the immediate precautionary measure distance, in the downwind direction, as necessary.
FIREIf tank, rail tank car or highway tank is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for 800 meters (1/2 mile) in all directions.
Source: NTP, 1992 — via CAMEO Chemicals (NOAA), public domain. Entry: 4,4'-ISOPROPYLIDENEDIPHENOL.
§ 07 · Handling and storage
Bisphenol A computed storage compatibility
Derived from CLP Annex VI classification and CAMEO reactive-group data — not copied from a PDF.
Full interactive verdict — reactions, gas release on contact, ADR forms →
§ 09 · Physical and chemical properties
Bisphenol A physical properties
Fire-relevant values first — flash point and explosion limits decide the storage and ventilation regime.
Flash point
79.4 °C
Source: CAMEO Chemicals (NOAA, public domain); per-value source references stored in the database.
§ 10 · Stability and reactivity
Reactive group (CAMEO/NOAA): Phenols and Cresols. Our database documents 17 incompatible and 14 caution reaction-partner groups for bisphenol A — including which combinations release gas on contact. See the per-partner breakdown with gas release →
17
Incompatible
14
Caution
§ 13 · Disposal considerations
Dispose of waste and residues in accordance with local and national regulations — in the EU under the Waste Framework Directive 2008/98/EC. Never discharge to drains or municipal waste; hand contaminated packaging and unused product to an authorised waste-disposal company. The supplier's SDS section 13 lists the applicable waste codes for the specific product.
MSDS vs SDS
Bisphenol A MSDS vs SDS: is there a difference?
MSDS (Material Safety Data Sheet) is the older name for the same document. In the US, OSHA's Hazard Communication Standard (2012) adopted the GHS-standardised 16-section Safety Data Sheet; in the EU the format is set by REACH Annex II. So a "bisphenol A MSDS" and a "bisphenol A SDS" refer to the same document — today it is issued as an SDS. Full breakdown of the differences →
Substance profile
What bisphenol A is
Physical and chemical properties with the conditions each value was measured under, synonyms, formula and the harmonised CLP classification →
Compliance hub
From classification to SDS
The classification above corresponds to Section 2 of a Safety Data Sheet. Learn how a compliant 16-section SDS is structured and authored →
GHS label maker
Build the label for bisphenol A
Pictograms, signal word and H-statements combined into a compliant label layout →
§ 16 · Sources
- Classification: Regulation (EC) No 1272/2008 (CLP), Annex VI
- Transport: UN ADR 2025 (UNECE), Table A
- Reactivity: NOAA CAMEO Chemicals reactive-group matrix (public domain)
- Physical properties: CAMEO Chemicals (NOAA, public domain) — per-value source references stored in the database
- Emergency response (§4–§6): ERG 2024 (PHMSA) · NIOSH Pocket Guide (CDC) · CHRIS (USCG) · NTP · EPA — via CAMEO Chemicals (NOAA), all US federal public domain, reproduced verbatim
- Substance data: PubChem · ECHA
Reference aid only. This page summarises the harmonised EU classification and computed storage guidance — it is not a Safety Data Sheet and does not replace one. Always verify hazards, handling and storage against the supplier's SDS (sections 7 and 10) and local regulations before use. Page updated 2026-08-11.
Frequently asked questions about bisphenol A
Is an MSDS the same as an SDS?
In practice, yes. MSDS (Material Safety Data Sheet) is the older name for the same document. In the US, OSHA's Hazard Communication Standard (2012) adopted the GHS-standardised 16-section Safety Data Sheet; in the EU the SDS format is set by REACH Annex II. A document you find labelled "bisphenol A MSDS" is today issued as an SDS.
What GHS pictograms does bisphenol A require?
Under the harmonised EU classification (CLP Annex VI), bisphenol A carries GHS05 and GHS07 and GHS08 and GHS09 with the signal word "Danger". Hazard statements: H360F, H335, H318, H317, H400, H410. A supplier's SDS may add self-classified hazards on top of this harmonised minimum.
Where can I download an official bisphenol A SDS PDF?
From your own supplier — an SDS is issued per product and supplier, so the correct PDF for an inspection is the one matching the product you actually purchased. The supplier links on this page lead to the official SDS libraries of major distributors.
Call emergency services first
112 in the EU · 911 in the US. This screen is published response information, not medical advice, and it does not replace emergency services, a poison centre or the supplier's safety data sheet.
Text below is the CAMEO Chemicals entry 4,4'-ISOPROPYLIDENEDIPHENOL — confirm it matches the form in front of you.
01 · First aid
What to do for the person
EYES
First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop.
SKIN
IMMEDIATELY flood affected skin with water while removing and isolating all contaminated clothing. Gently wash all affected skin areas thoroughly with soap and water. If symptoms such as redness or irritation develop, IMMEDIATELY call a physician and be prepared to transport the victim to a hospital for treatment.
INHALATION
IMMEDIATELY leave the contaminated area; take deep breaths of fresh air. If symptoms (such as wheezing, coughing, shortness of breath, or burning in the mouth, throat, or chest) develop, call a physician and be prepared to transport the victim to a hospital. Provide proper respiratory protection to rescuers entering an unknown atmosphere. Whenever possible, Self-Contained Breathing Apparatus (SCBA) should be used; if not available, use a level of protection greater than or equal to that advised under Protective Clothing.
INGESTION
DO NOT INDUCE VOMITING. If the victim is conscious and not convulsing, give 1 or 2 glasses of water to dilute the chemical and IMMEDIATELY call a hospital or poison control center. Be prepared to transport the victim to a hospital if advised by a physician. If the victim is convulsing or unconscious, do not give anything by mouth, ensure that the victim's airway is open and lay the victim on his/her side with the head lower than the body. DO NOT INDUCE VOMITING. IMMEDIATELY transport the victim to a hospital.
02 · Fire
Extinguishing and tactics
Fire and explosion hazard
This chemical is combustible. This compound may form explosive dust clouds. Static electricity can cause its dust to explode.
Extinguishing media and tactics
Fire Extinguishing Agents: Foam, dry chemical, carbon dioxide
03 · Spill
Containment, isolation, evacuation
Containment and clean-up
SMALL SPILLS AND LEAKAGEShould a spill occur while you are handling this chemical, FIRST REMOVE ALL SOURCES OF IGNITION, then you should dampen the solid spill material with 60-70% ethanol and transfer the dampened material to a suitable container. Use absorbent paper dampened with 60-70% ethanol to pick up any remaining material. Seal the absorbent paper, and any of your clothes, which may be contaminated, in a vapor-tight plastic bag for eventual disposal. Solvent wash all contaminated surfaces with 60-70% ethanol followed by washing with a soap and water solution. Do not reenter the contaminated area until the Safety Officer (or other responsible person) has verified that the area has been properly cleaned.
STORAGE PRECAUTIONSYou should store this chemical under ambient conditions, and keep it away from oxidizing materials.
Initial isolation and evacuation
IMMEDIATE PRECAUTIONARY MEASUREIsolate spill or leak area in all directions for at least 50 meters (150 feet) for liquids and at least 25 meters (75 feet) for solids.
SPILLIncrease the immediate precautionary measure distance, in the downwind direction, as necessary.
FIREIf tank, rail tank car or highway tank is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for 800 meters (1/2 mile) in all directions.
Sources: ERG 2024 (PHMSA) · NIOSH Pocket Guide (CDC) · CHRIS (USCG) · NTP · EPA — via CAMEO Chemicals (NOAA), public domain. Text reproduced verbatim.